User Tools

Site Tools


eduroam_linux

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
eduroam_linux [2014/12/11 16:22]
costesbn created
eduroam_linux [2014/12/22 14:01] (current)
costesbn typo
Line 1: Line 1:
 ====== eduroam setup for Linux ====== ====== eduroam setup for Linux ======
  
-The following instructions assume using the NetworkManager. The graphical interface might differ a bit from the below screenshots depending on the desktop environment in use, but the required data should be the same. Two protocols can be used for authentication using HITS eduroam IDs: PEAP/​MSCHAPv2 and TTLS/​MSCHAPv2. The two protocols are similar, there is no preference for using one or the other.+The following instructions assume using the NetworkManager; they were tested on Fedora Linux 20. The graphical interface might differ a bit from the below screenshots depending on the desktop environment in use, but the required data should be the same. Two protocols can be used for authentication using HITS eduroam IDs: PEAP/​MSCHAPv2 and TTLS/​MSCHAPv2. The two protocols are similar, there is no preference for using one or the other.
  
 **Step 1.** Click on the WiFi icon, typically found in the upper right screen corner, and choose "​eduroam"​. **Step 1.** Click on the WiFi icon, typically found in the upper right screen corner, and choose "​eduroam"​.
Line 16: Line 16:
   * PEAP version: Automatic   * PEAP version: Automatic
   * Inner authentication:​ MSCHAPv2   * Inner authentication:​ MSCHAPv2
-  * Username: <your username>​@h-its.org +  * Username: ​//<your username>​//@h-its.org 
-  * check "Ask for this password every time", or (not recommended) enter the password. ​The is the same password that you use to access your e-mail.+  * check "Ask for this password every time", or (not recommended) enter the password. ​This is the same password that you use to access your e-mail.
  
 Using TTLS/​MSCHAPv2 requires the following settings: Using TTLS/​MSCHAPv2 requires the following settings:
Line 27: Line 27:
   * CA certificate:​ download {{:​hits-eduroam-ca.der|the certificate}} to your computer, then select it   * CA certificate:​ download {{:​hits-eduroam-ca.der|the certificate}} to your computer, then select it
   * Inner authentication:​ MSCHAPv2   * Inner authentication:​ MSCHAPv2
-  * Username: <your username>​@h-its.org +  * Username: ​//<your username>​//@h-its.org 
-  * check "Ask for this password every time", or (not recommended) enter the password. ​The is the same password that you use to access your e-mail.+  * check "Ask for this password every time", or (not recommended) enter the password. ​This is the same password that you use to access your e-mail.
  
 **Step 3.** Click on the WiFi icon again and choose "​eduroam"​. If "Ask for this password every time" was checked (as recommended) in Step 2, you'll be asked for a password - this is the same password that you use to access your e-mail. After entering the password, the authentication should succeed and access to the "​eduroam"​ network should be granted. **Step 3.** Click on the WiFi icon again and choose "​eduroam"​. If "Ask for this password every time" was checked (as recommended) in Step 2, you'll be asked for a password - this is the same password that you use to access your e-mail. After entering the password, the authentication should succeed and access to the "​eduroam"​ network should be granted.
  
eduroam_linux.1418314953.txt.gz · Last modified: 2014/12/11 16:22 by costesbn